DIN 126
| Autor: | Johannes Reinhardt |
|---|---|
| Lizenz: | LGPL 2.1+ |
| Kollektion: | Washers |
| Identisch mit: | ISO 7091, DIN ISO 7091, DINENISO 7091 |
| Status: | active |
| Standardisierungsbehörde: | DIN |
| ID: | DIN126 |
| Quellen: | http://almetal.nl/en/techinfo/wsh/wd126.htm |
Zeichnungen
| Parametername | Beschreibung |
|---|---|
| d1 | Innendurchmesser |
| d2 | Aussendurchmesser |
| key | Gewindebezeichnung |
| s | Dicke |
Beschreibung
Plain washer, metric sizes
FreeCAD
| Autor: | Johannes Reinhardt |
|---|---|
| Lizenz: | LGPL 2.1+ |
OpenSCAD
| Autor: | Johannes Reinhardt |
|---|---|
| Lizenz: | LGPL 2.1+ |
Aufruf
module DIN126(key="M10", part_mode="default")
function DIN126_dims(key="M10", part_mode="default")
function DIN126_conn(location,key="M10", part_mode="default")Konnektoren
| Ort | Zeichnung |
|---|---|
| top |  |
| bottom |  |
| outer |  |
Tabellen
| key | d1 (mm) | d2 (mm) | s (mm) |
|---|---|---|---|
| M5 | 5.5 | 10.0 | 1.0 |
| M6 | 6.6 | 12.0 | 1.6 |
| M7 | 7.6 | 14.0 | 1.6 |
| M8 | 9.0 | 16.0 | 1.6 |
| M10 | 11.0 | 20.0 | 2.0 |
| M12 | 13.5 | 24.0 | 2.5 |
| M14 | 15.5 | 28.0 | 2.5 |
| M16 | 17.5 | 30.0 | 3.0 |
| M20 | 22.0 | 37.0 | 3.0 |
| M22 | 24.0 | 39.0 | 3.0 |
| M24 | 26.0 | 44.0 | 4.0 |
| M27 | 30.0 | 50.0 | 4.0 |
| M30 | 33.0 | 56.0 | 4.0 |
| M33 | 36.0 | 60.0 | 5.0 |
| M36 | 39.0 | 66.0 | 5.0 |
| M39 | 42.0 | 72.0 | 6.0 |
| M42 | 45.0 | 78.0 | 7.0 |
| M45 | 48.0 | 85.0 | 7.0 |
| M48 | 52.0 | 92.0 | 8.0 |
| M52 | 56.0 | 98.0 | 8.0 |
| M56 | 62.0 | 105.0 | 9.0 |
| M60 | 66.0 | 110.0 | 9.0 |
| M64 | 70.0 | 115.0 | 9.0 |
| M72 | 78.0 | 125.0 | 10.0 |
| M80 | 86.0 | 140.0 | 12.0 |
| M90 | 96.0 | 160.0 | 12.0 |
| M100 | 107.0 | 175.0 | 14.0 |